Suzhou Hengxie Machinery Co., Ltd
Suzhou Hengxie Machinery Co., Ltd
Add to Cart
HXE-17DST Medium copper wire drawing machine with annealer
I. Quick details
HXE-17DST Medium copper wire drawing machine with annealer is used to draw and anneal single bare copper wire from 2.6mm-3.5mm to 0.4mm-1.6mm.
II. Compositions of equipments
| Name | Quantity |
| 1. Pay-off(Wire Tangle Auto Stop) | 1 set |
| 2. HXE-17DS Drawing machine | 1 set |
| 3. HXE-TH250 Annealing machine | 1 set |
| 4. HXE-180 Tension controller | 1 set |
| 5. HXE-SX500 Single or Double spoolers | 1 set |
| 6. Electric cabinet | 2 set |
| 7. Operation panel | 1 set |
| 8. Steam generator | 1 set |
| 9. Gear Oil Lubrication System | 1 set |
| 10. Spare parts | 1 set |
III.Main technical parameters
| Machine type | HXE-17DT | HXE-17DST | HXE-17HST |
| Control system | Traditional analog type/digital control with production record | ||
| Outlet diameter | 0.4-1.2mm | 0.4-1.6mm | 0.4-1.8mm |
| Inlet diameter | 2.6-3.0mm | 2.6-3.5mm | 2.6-3.5mm |
| Max line speed | 1200 | 2000 | 1800 |
| Dies No | 17 | 17 | 17 |
| Slip ratio | 18%+12.5% | 20%+15% | 19.5%+10% |
| Frame | Iron cast | Welded by steel plate | |
| Capstan | Tungsten | ||
| Max capstan diameter | 260mm | 250mm | 280mm |
| Fix speed capstan diameter | 260mm | 250mm | 280mm |
| Spooler bobbin size | 400-630mm | ||
| Bobbin loading&unloading type | Double end thimble | ||
| Max.loading capacity | 500KG/MAX | ||
| Transmission type | By chain | By precision helical gears | |
| Traversing unit | 90W belt type redule motor | ||
| Brake | Magnetic brake/Disc brake | ||
| Revise system | PID Synchronous control spooler | ||
| Detecting device | Weight balance by swing arm | ||
| Tension control | By air pressure adjust | ||
| Main motor | 37kw | 55kw | 45kw |
| Spooler motor | 11kw | 11kw | 11kw |
| Annealing method | DC.Three-section annealing | ||
| Max annealing current | DC1200A | DC2000A | DC2000A |
| Max annealing voltage | DC50V | DC50V | DC50V |
| Annealing power | 60KVA | 100KVA | 100KVA |
| Steam quantity | 12kg/h | 12kg/h | 18kg/h |
| Cooling water capacity | 300L/min | 400L/min | 500L/min |
| Capacity of compressed air | 0.4~0.6Mpa,30L/min | 0.4~0.6Mpa,50L/min | 0.4~0.6Mpa,50L/min |
| Power source | 380V50/60HZ | ||
| Machine dimension | 13300*3500*3400(mm) | ||
| Machine weight | 6500KG | 7500KG | 6500KG |
IV. Operation & Maintenance
4-1. Preparation before running
Check all the lubrication parts of the transmission parts.
Check Wire-break Auto stop device, Safety doors.
Check coolant water, Lubrication oil, Steam, Compressed air.
After checking, jogging machine as lower than 5m/s, check all parts again.
4-2. Operation
Connect power.
Prepare the drawing dies.
Prepare the wire pointing and threading.
According to the die list, place the wires on the capstan, wire goes through each layer 2-3 times.
Put wire through the fix speed capstan then through the annealer machine
Annealer machine wire path, please check the Wire path drawing on the machine.
Then put wire through the Wire passing wheels, Tension device, Spooler machine.
After the wire path, close Safety door, adjust Drawing lubrication oil, Coolant water, Steam, Compressed air.
4-3. Diameter, Voltage, Current, Speed linkage
Our machine is made according to use`s elongation requirement, nothing to do with copper wire.
Annealing voltage & Speed
4-4. Maintenance
Lubricate all the parts, make sure all the wheels and capstans run flexible.
After working 1000hours, clean all the bearing and change new lubrication oil.
Annealing contact rings are consuming parts, after using for certain time, when annealing, will have sparks, which means you need change new rings.
There are carbon brushes on the back side of the annealer machine, need change accordingly.
