Suzhou Hengxie Machinery Co., Ltd
Suzhou Hengxie Machinery Co., Ltd
Add to Cart
HXE-13DLA Aluminium rod breakdown machine with online annealing machine
I. Quick description
HXE-13DLA Aluminium rod breakdown machine with annealing machine is used to draw and anneal single bare aluminium wire from 9.5mm to 1.7mm-4.2mm.
II. Component
| 1. Pay-off shelf | 1 set |
| 2. HXE-13DLA Aluminium rod breakdown machine | 1 set |
| 3. HXE-TH350 Annealing machine | 1 set |
| 4. HXE-180 Tension controller | 1 set |
| 5. HXE-WF650 Coiler (Optional, Not concluded in the quotation) | 1 set |
| 6. HXE-SX630 Double spoolers | 1 set |
| 7. Electrical cabinet | 2 set |
| 8. Operation panel | 1 set |
| 9. Spare parts for One year | 1 set |
| 10. Gear Oil System (Pump,Cooler, others) | 1 set |
III. Parameter
1. Inlet wire diameter 9.5mm
2. Outlet wire diameter 1.7mm-4.2mm
3. Actual drawing & annealing speed 800m/min
4. Number of Dies 13
5. Drum speed ratio 1.25
6. Capstan Iron cast, With Tungsten Carbide surface, 650mm, 4 pieces
7. Machine frame Welded
8. Main motor AC 75KW, Fix speed motor 22KW
9. Spooler motor AC 11KW
10. Inverter Inovance Brand
11. Speed adjust by Inverters
12. Transmission by Gear&Triangle Belts
13. Cantilever type pay-off shelf
14. Free rod type traversing
15. Power source customized
16. Annealing voltage 60V
17. Annealing current 3000A
18. Annealing power 180KVA
19. Annealing type D.C. Three section annealing
20. Annealing speed control by Inverters , auto tracking the drawing speed
IV. Lifting the machine, installation, adjustment
4-1. Lifting, there are four lifting rings to lift.
4-2. Installation, please check the external drawing and foundation drawing of the machine, dig the ground, put the machine in position, check the horizontal level, adjust the ground screws, put concrete slurry, after dry and fix, check the horizontal level again, then fix the machine by the ground screws.
4-3. Adjustment, clean all parts, check all the part no loose.
V. Preparation before working
5-1. Check all parts lubrication conditions,
5-2. Check drawing lubrication oil, cooling water, steam, air pressure.
5-3. After checking, connect to power, according to the Electrical drawing, use foot switch, to make the machine operating in low speed (under 4m/s), if no Abnormal, then can begin to work.
VI. Operating procedures
6-1. Open power switch
6-2. According to the wire diameter, choose the dies (Check the die list).
6-3. Use pliers to break the wire to get a smaller section.
6-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).
6-5. Wire direction, please check the Drawing for Wire path.
6-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.
6-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.
6-8. Set the length meters, then press the Start button to start the machine.
