Suzhou Hengxie Machinery Co., Ltd
Suzhou Hengxie Machinery Co., Ltd
Add to Cart
HXE-24DT Fine copper wire drawing machine with annealing machine
I. Quick description
HXE-24DT Fine copper wire drawing machine with annealing Machine is used to draw and anneal single bare copper wire from 0.5mm-1.0mm to 0.07mm-0.25mm.
II. Components
| Name | Quantity | |
| 1. Pay-off shelf | 1 set | |
| 2. HXE-24DT Drawing&Annealing machine | 1 set | |
| 3. Electrical control system | 1 set | |
| 4. Steam generator | 1 set | |
| 5. Lubrication Tank and Pump | Optional | |
| 6. Spare parts | As per List | |
| 7. Operation Manual, Inverter Manual | ||
III. Main Technical parameters
1. Usage single bare copper wire drawing and annealing
2. Inlet size 0.5mm-1.0mm
3. Outlet size 0.07mm-0.25mm (Elongation of annealed wire 25% to 32%)
4. Machine speed/max 1800m/min
5. Die number 24, Dies size 25mm×8-10mmT, Slip ratio 13%+8%
6. Wire drawing mode standing-mode and 4axes
7. Drive by Inverter control, Brand Inovance, Most widely used brand in drawing machine
8. Main motor 15KW, Spooler motor 3.7KW, China best brand
9. Annealing voltage DC50V/max, Annealing current DC300A/max, Annealing power 15KVA
10. Annealing method DC Three section annealing
11. Annealing protection will be done by steam protection
12. Capacity of compressed air 0.4-0.6Mpa, 20L/min
13. Demand Water quantity for annealing and coolant 200L/min
14. Machine frame welded by steel plate
15. Transmission Flat belts
16. Capstan Ceramic plasma
17. Lubricating system Pipe Spray
18. Bobbin size 300mm, loading capacity: 50kg/max
19. Bobbin loading & unloading type shaft type
20. Traversing unit 110W synchros motor, width: 270mm/max
21. Tension control by Air pressure tension control (With Weight balance as Backup)
22. Cabinet 0.8m*0.6m*2.0m
23. Machine dimension 2.3m*1.6m*1.9m; Installation Area 3.3m*1.7m+0.8*0.6m
24. Machine weight 3400KG, Cabinet weight 500KG. In total for shipping around 4,000KG.
IV. Advantage and after-sale service
A: Advantage
(1). HENGXIE has some world famous parts suppliers, has special lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our own factory , quality is reliable.
(3). Our company’s developing process in more than 10 years.
(4). DC. three-section annealing
B: After-self service
Our company for all machine product, since the shipment date, our company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
V. Preparation before working
5-1. Check all parts lubrication conditions,
5-2. Check drawing lubrication oil, cooling water, steam, air pressure.
5-3. After checking, connect to power, according to the Electrical drawing, use foot switch, to make the machine operating in low speed (under 4m/s), if no Abnormal, then can begin to work.
VI. Operating procedures
6-1. Open power switch
6-2. According to the wire diameter, choose the dies (Check the die list).
6-3. Use pliers to break the wire to get a smaller section.
6-4. Use pliers to make the wire through the dies, then pull the wire out (Use foot switch to make the machine running in a low speed to make the wire move).
6-5. Wire direction, please check the Drawing for Wire path.
6-6. After make the wire through all the parts, close the annealing door and the spooling door, make the tension swing arm in the lowest position. and in running, the balance arm should be in the horizontal line. No big shake, no up and down frequently.
6-7. Open the Annealing switch, open the Pump, open and adjust the Drawing lubrication oil, Cooling water, Steam, Compressed air.
6-8. Set the length meters, then press the Start button to start the machine.
